Acu-rite CSS I/O Users Manual Uživatelský manuál Strana 1

User’s ManualCSS I/OEnglish (en)2/2010ACU-RITE®

8 I Operating InstructionsI - 2 Spindle Speed Control (RPM)I - 2 Spindle Speed Control (RPM)Milling SystemsThe Mill Spindle Speed Control is for mill

CSS I/O 9I - 2 Spindle Speed Control (RPM)Mill Spindle Installation setupThe configuration parameters are found under Installation Setup. The Spindl

10 I Operating InstructionsI - 2 Spindle Speed Control (RPM)Voltage Offset / RPM SourceThe voltage offset field is used to adjust for any inherent of

CSS I/O 11I - 2 Spindle Speed Control (RPM)Voltage / RPM SetupThe voltage setup fields are used to establish the relationship between the DAC output

12 I Operating InstructionsI - 2 Spindle Speed Control (RPM)Operation / Job ExecutionThe operation of the Mill Spindle is associated with the use of

CSS I/O 13I - 2 Spindle Speed Control (RPM)A tool can be run from the tool table, or by pressing enter after defining the spindle parameters for a to

14 I Operating InstructionsI - 3 Controlling the Constant Surface Speed (CSS)I - 3 Controlling the Constant Surface Speed (CSS)In CSS mode, a constan

CSS I/O 15I - 3 Controlling the Constant Surface Speed (CSS)Configuration of CSSTo use the CSS functionality, the last axis must be defined as a rota

16 I Operating InstructionsI - 3 Controlling the Constant Surface Speed (CSS)CSS operating modeThe operating parameters are set in the CSS / DIRECT R

CSS I/O 17I - 3 Controlling the Constant Surface Speed (CSS)Activating the DAC outputAfter selecting the operating mode and entering its parameters,

18 I Operating InstructionsI - 3 Controlling the Constant Surface Speed (CSS)Connecting the CSS I/O to the inverter of the latheExample of gear detec

CSS I/O 19I - 4 DiagnosticsI - 4 DiagnosticsGeneral InformationWhen the CSS I/O box is connected to the DRO, the DIAGNOSTICS menu under INSTALLATION

20 I Operating InstructionsI - 4 DiagnosticsCSS, and Mill SpindleCSS / MS DIAGNOSTICS shows the status of the communication via the CAN bus and the s

CSS I/O 21I - 4 DiagnosticsFor CSS only, the MS INPUT/OUTPUT field shows the state relay outputs. The IN: field of the switching inputs is not used,

22 I Operating InstructionsI - 4 Diagnostics

CSS I/O 23IndexAActivating the DAC output ... 17CConfiguration of CSS ... 9, 15Connecting the CSS I/O to the inverterof the lathe ... 18Connecting the

Index

638296-22 Ver 00 Printed in USA Subject to change without notice 02/2010333 East State ParkwaySchaumburg, IL 60173-5337 USAHEIDENHAIN CORPORATI

CSS I/O 1I General Information ... 4Connecting the CSS I/O to X101 (turning) ... 4I - 1 Execution of Switching Functions ... 5Switching inputs

2

CSS I/O 3Operating Instructions

4 I Operating Instructions General InformationGeneral InformationConnecting the CSS I/O to X101 for executing switching functions (milling) or contro

CSS I/O 5I - 1 Execution of Switching FunctionsI - 1 Execution of Switching FunctionsIf you want to use both the CSS I/O and the KT 130 edge finder a

6 I Operating InstructionsI - 1 Execution of Switching Functions8 The CONDITION field is used to assign an axis to the output and to specify whether

CSS I/O 7I - 1 Execution of Switching FunctionsIn PULSED mode, the relay is activated (ON or OFF) for a specific period of time. After the period has